pe can't read the solid-state drive Causes and solutions: the first type: hard disk failure. Most of this situation occurs on the newly purchased assembly machine. Due to improper installation of the hard disk and the hardware failure of the hard disk itself, poor-quality hard disks are purchased.
PE does not recognize the hard disk because the motherboard turns on AHCI, while PE does not have relevant drivers. You only need to enter bios to change the mode to Ide. First of all, enter the BIOS setting interface and press DEL to turn on (different motherboards are slightly different). Select the Advanced tab.
Lack of corresponding drivers: In some PE systems, drivers may not contain all hardware devices, including hard drivers. This may cause the hard disk to be unrecognizable in the PE system.
1. In the PE disk environment, after starting DiskGenius, you can find the hard disk information in the list on the left, including the name, size, partition and other information of the hard disk, and support formatting, partitioning and other operations of the hard disk.
2. Running the WinPM tool in the PE system, it can still be seen that the WinPE system has recognized the mobile disk (disk 1), but the disk character has not been assigned to it.
3. The solution is to change the hard disk mode to IDE. The specific operation method is as follows: power-on --- when the large LENOVO screen appears on the screen --- press F2 to enter the BIOS. After entering the BIOS, you can press the left and right up and down keys to adjust the options, and then select A Dvanced.
1. Step 1: Insert the USB flash drive and start the computer. Step 2: Select the USB flash drive as the boot device and enter the system installation interface. Step 3: Select "Custom Installation" or similar options. Step 4: Select the hard disk to install the system and click the "New" button. Step 5: Set the size of the partition as needed and select the file system type.
2. You can use the USB disk startup tool "Youqitong" to install PE to the computer hard disk. The steps are as follows: open the software, select "local mode", select the installation disk symbol and click "Install". Prompt "About to be installed on the local hard disk", click "Confirm" to continue the installation.
3, WFor the IN10/W7 system, please use a USB flash drive above 8G, and a USB flash drive above 4G for the XP system. The larger the capacity, the more systems will be stored. Download PE boot USB disk production software such as depth and cabbage, and follow the prompts to make the boot disk.
4. You can use a USB flash drive to start the production tool "Youqitong" to install PE on the hard disk of the computer. The steps are as follows: open the software, select "Local Mode", select "Install", and click "Install". Pop up the "About to install to the local hard disk" selection box, click "Confirm" to continue the installation.
5. Steps to install WinPE in the system image to the hard disk: 1. Of course, the first step is to download the system image file from the Internet. This image file can not only be used to install the operating system, but also to extract the tools in it. WinPE is one of the tools. First Unzip the image file.
Binance market-APP, download it now, new users will receive a novice gift pack.
pe can't read the solid-state drive Causes and solutions: the first type: hard disk failure. Most of this situation occurs on the newly purchased assembly machine. Due to improper installation of the hard disk and the hardware failure of the hard disk itself, poor-quality hard disks are purchased.
PE does not recognize the hard disk because the motherboard turns on AHCI, while PE does not have relevant drivers. You only need to enter bios to change the mode to Ide. First of all, enter the BIOS setting interface and press DEL to turn on (different motherboards are slightly different). Select the Advanced tab.
Lack of corresponding drivers: In some PE systems, drivers may not contain all hardware devices, including hard drivers. This may cause the hard disk to be unrecognizable in the PE system.
1. In the PE disk environment, after starting DiskGenius, you can find the hard disk information in the list on the left, including the name, size, partition and other information of the hard disk, and support formatting, partitioning and other operations of the hard disk.
2. Running the WinPM tool in the PE system, it can still be seen that the WinPE system has recognized the mobile disk (disk 1), but the disk character has not been assigned to it.
3. The solution is to change the hard disk mode to IDE. The specific operation method is as follows: power-on --- when the large LENOVO screen appears on the screen --- press F2 to enter the BIOS. After entering the BIOS, you can press the left and right up and down keys to adjust the options, and then select A Dvanced.
1. Step 1: Insert the USB flash drive and start the computer. Step 2: Select the USB flash drive as the boot device and enter the system installation interface. Step 3: Select "Custom Installation" or similar options. Step 4: Select the hard disk to install the system and click the "New" button. Step 5: Set the size of the partition as needed and select the file system type.
2. You can use the USB disk startup tool "Youqitong" to install PE to the computer hard disk. The steps are as follows: open the software, select "local mode", select the installation disk symbol and click "Install". Prompt "About to be installed on the local hard disk", click "Confirm" to continue the installation.
3, WFor the IN10/W7 system, please use a USB flash drive above 8G, and a USB flash drive above 4G for the XP system. The larger the capacity, the more systems will be stored. Download PE boot USB disk production software such as depth and cabbage, and follow the prompts to make the boot disk.
4. You can use a USB flash drive to start the production tool "Youqitong" to install PE on the hard disk of the computer. The steps are as follows: open the software, select "Local Mode", select "Install", and click "Install". Pop up the "About to install to the local hard disk" selection box, click "Confirm" to continue the installation.
5. Steps to install WinPE in the system image to the hard disk: 1. Of course, the first step is to download the system image file from the Internet. This image file can not only be used to install the operating system, but also to extract the tools in it. WinPE is one of the tools. First Unzip the image file.
317.31MB
Check664.14MB
Check876.18MB
Check631.17MB
Check487.89MB
Check528.45MB
Check861.19MB
Check977.84MB
Check836.27MB
Check387.19MB
Check763.51MB
Check336.88MB
Check223.18MB
Check287.38MB
Check383.63MB
Check911.37MB
Check295.45MB
Check549.71MB
Check625.14MB
Check644.34MB
Check289.17MB
Check795.41MB
Check661.36MB
Check873.54MB
Check185.69MB
Check987.21MB
Check175.37MB
Check939.83MB
Check519.52MB
Check397.34MB
Check259.45MB
Check666.17MB
Check198.67MB
Check971.26MB
Check683.33MB
Check153.56MB
CheckScan to install
Binance market to discover more
Netizen comments More
276 百无一用网
2025-01-23 04:43 recommend
2014 土崩瓦解网
2025-01-23 03:49 recommend
1869 微不足道网
2025-01-23 03:22 recommend
1068 惊涛骇浪网
2025-01-23 02:53 recommend
374 拜倒辕门网
2025-01-23 02:11 recommend